Can I Install a Bath Tub Myself? Considerations And Also Steps
Can I Install a Bath Tub Myself? Considerations And Also Steps
Blog Article
Are you on the lookout for facts and techniques around How to Install a Bathtub Yourself?
Setting up a bath tub isn't specifically brain surgery, but it does require solid plumbing, carpentry, and in some cases, tiling abilities. Changing an old bath tub with a new one is likewise a reasonably hard project. If the old bathtub is conveniently accessible, the project can move quickly; if you have to open a wall to remove the old tub and position the new bathtub, the task is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub and set in the new one. Ensure you have actually certified on your own for the work and also fit trying it. As opposed to working with a service provider to take control of a halfway-completed task, it is far better to take into consideration using one prior to you begin. Opportunities are you might need a professional plumber to make tube connections.
This write-up will certainly assist you set up a new bathtub in your bathroom if you have actually currently bought a brand-new bathtub as well as don't need to transform the setup of your previous water system pipes.
Your tools and also product checklist need to comprise the following:
Getting ready for the Installment
Firstly, the sustaining structure supplied with the bath must be fitted (if required) according to the producer's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is important to make certain that if the faucet features a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop strain on the bathtub.
Fit the versatile faucet ports to the bottom of the two faucets using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its final placement.
Removing Old Taps
If you need to replace old faucets with new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, activate the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be fairly bothersome due to the restricted gain access to that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a fabric prepared for the continuing to be water that will come from the pipes. When the supply pipelines have actually been removed, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from transforming throughout this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing substance.
Prior to moving on to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Installing the Tub
Utilizing the two wood boards under its feet, put the tub in the called for placement. The wood boards are handy in equally spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto four small points.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bath tub till the level reviews degree.
To mount faucets, fit all-time low of the furthest flexible faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Switch on the water supply and check all joints as well as new pipework for leakages and tighten them if essential. Fill up the bathtub as well as likewise examine the overflow electrical outlet and the regular outlet for leakages.
Lastly, fix the bathroom paneling as described in the supplier's instruction manual. Tiling and also sealing around the bath tub must wait until the tub has been made use of at least when as this will resolve it into its last setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the installing opening in the bath/basin making sure that the washers remain in location between the faucet as well as the sink. Secure the faucet in place with the supplier offered backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with regular tap adapters. The former kind ought to be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to split a rigid seal, triggering the water to pass through the wall in between the bath as well as the tiling, leading to issues with wetness as well as feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your fixtures as well as installations. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always fill the tub with water before securing, to allow for the movement experienced when the bathtub remains in use. The sealant can split rather early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily available on the market. It is a good idea to fit the floor tiles making use of water-resistant or waterproof sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our post on Tools You Need to Install a New Bathtub . Thank you for finding the time to read through our piece of content. Enjoyed reading our write-up? Please share it. Let others find it. I take joy in reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Request Service
Report this page